Driving question: How well can a quadratic equation in standard form describe the path of a ball rolling across an inclined surface?
a controls the direction and amount of curvature; b helps determine the horizontal placement and axis of symmetry; c is the predicted y-intercept. We will find these values from measured data using Desmos—not by guessing the coefficients.
Part 1 · Set up and create a curved trail 5 points
Materials
- Large paper, ideally 11 × 17 inches or larger
- Rigid board or tray and a book/block to make a gentle slope
- Small smooth ball; teacher-approved washable, water-based marking material
- Tape, ruler, pencil, paper towels
- Calculator or device with Desmos
Group roles
Launcher: secures board and rolls ball.
Measurer: establishes axes and records coordinates.
Desmos analyst: inputs points, runs regression and checks results.
All three students contribute to the written analysis; rotate jobs after practice attempts.
- Tape the paper flat to a gently raised board. Place it where the ball can be caught safely.
- Mark a horizontal x-axis and a perpendicular uphill y-axis. Put the origin near the bottom-left, with both scales in centimeters.
- Lightly dampen the ball using the approved marking method; avoid excess water that smears.
- Roll diagonally uphill and across. Practice until you obtain one continuous, visibly curved trail with a highest point and a section on each side.
- Circle your clearest trail. Mark the measured coordinate points on that trail. Keep the original sheet or photograph it clearly.
Part 2 · Record exactly 5 points 6 points
Select five different points along your chosen trace. Choose at least two before and two after the approximate highest point, with one near the top. Space the points across the trail rather than clumping them together. Use your axes to read (x, y), in centimeters.
| Point | x (cm) | y (cm) | Where is it on the trail? |
|---|
Practice data are fictional and must be replaced with your own measurements for submission. If the ball's mark is too broad, measure the center of the trail consistently.
Measurement self-check
Do all five x-values differ? Did you record centimeters consistently? Are your points spread from left to right? If the trajectory has a visible peak, do your five points include data on both sides of it? Do not move points just to improve the regression.
Part 3 · Graph your physical evidence 4 points
Plot all five points on graph paper or the coordinate grid below. Label the horizontal and vertical axes, show a sensible numerical scale and units, and sketch a smooth curve through the measured trail. Do not connect points with straight line segments as your final model.
Part 4 · Use Desmos quadratic regression 8 points
What regression does
Regression finds a quadratic that fits all five points together, instead of forcing the curve through only three points. Your measured points may not lie perfectly on one parabola because real measurements contain error.
- Open Desmos Graphing Calculator.
- Click + and choose Table. Enter your five x-values in the x₁ column and the matching y-values in y₁. (Or use the Copy button above to paste both columns into a blank expression line.)
- On a new expression line, type the regression statement below. The ~ symbol is a tilde, not an equal sign.
y₁ ~ ax₁² + bx₁ + cTyping version:
y_1 ~ a x_1^2 + b x_1 + c - Desmos estimates a, b and c. Record them below, rounding to three decimal places unless more precision is needed.
- Find the displayed R² (coefficient of determination) in the regression results and record it. If Desmos displays something unexpected, confirm that you used ~, quadratic standard form and the five data pairs.
- In a new line, enter
y = ax² + bx + cto display your model over the data. Check that the curve is reasonably close to your five plotted points. - Save a screenshot showing the five-point table, quadratic regression, coefficient values, R², and graph. Include it with your submission.
Report your regression
Desmos troubleshooting and coefficient reminders
- Use x₁ and y₁ as your table column names (or match whatever Desmos shows).
- The regression needs a tilde (~), not =.
- Because the trace should open downward, you would usually expect a < 0. If not, re-check the axis directions and measured points—do not falsify the measurements.
- A change in the chosen origin changes the numerical values of b and c, so they are specific to your axes.
- For a typical fitted quadratic that includes an intercept, R² is between 0 and 1 (allowing for rounding); 1 means the five measured points lie exactly on the fitted curve.
Part 5 · Explain and evaluate your model 5 points
1. Interpret a. Is a positive or negative? What does that tell you about the shape of the path?
2. Interpret c. What does c represent on your axes? Did you actually measure the ball at x = 0, or is c a prediction?
3. Interpret R². Write your R² to at least three decimals. Convert it to a percentage (R² × 100%). Explain what that percentage means for this five-point dataset.
4. Evaluate reliability. Does a high R² prove the ball followed a perfect parabola? Identify one measurement or physical source of error.
5. Improve the experiment. Name one specific change that could make the data more consistent.
Part 6 · Submit and present 2 points
Submit one group report, the marked paper or a clear photo, and a Desmos screenshot. Each group member should be prepared to explain one part of the process.
Grading rubric · 30 points
| Category | Points | Full-credit evidence |
|---|---|---|
| Setup and physical trail | 5 | Clear curved path, safe setup, correctly labeled axes, recorded roles |
| Five-point measurements | 6 | Exactly 5 accurate, well-spaced coordinate pairs with units |
| Graph | 4 | All five points plotted, axes and scale labeled, shape accurately shown |
| Desmos regression | 8 | Correct quadratic regression, coefficients, standard-form equation, R², prediction check and screenshot |
| Interpretation and evaluation | 5 | Sound explanations of a, c, R², evidence, errors and improvement |
| Submission and collaboration | 2 | Complete evidence and meaningful contributions from all 3 |
| Total | 30 |
Teacher implementation notes
Suggested pacing: Day 1: setup, make the track, choose five coordinates and plot. Day 2: Desmos regression, R² analysis, writing, presentation.
Model: Students are analyzing y versus x in the plane of the inclined sheet—not position versus time. A gently inclined board with approximate constant across-slope motion and downhill acceleration can produce an approximately parabolic trail; actual rolling, friction, spin and dampness add error.
Safety / practicality: Use washable markings and test the ball/paper before class. A thin wet streak may be hard to read; a light, teacher-approved washable color or periodic overhead images can improve measurement. Watch for balls rolling off tables. Five distinct x-values are needed; do not assign fabricated observations.
Scoring note: Evaluate R² interpretation based on logic, not whether R² is close to 1; students should not be penalized for honest experimental imperfections.
Extension: Have groups compare R² using all five points to a second regression after adding additional real points, then discuss why more measurements change confidence.
Next Step: Model Quadratics with Python
After the quadratic lesson or measurement task, explore coefficients, vertices, and zeros in the guided starter. Then use collected data to write and evaluate your own quadratic regression model.
Predict first, build and run your program in the browser sandbox, then use the results to explain your model. Download your lab record when you finish.